Custom Search

Saturday, May 5, 2007

Tpis 4 : Trimming the Plane

The word “trimming” refers to the adjusting of your airplane controls during a flight so that the plane flies straight and level without you making any control inputs. Sometimes a model airplane will want to veer in one direction or another because of the motor's torque or perhaps some distortion or construction defect is affecting the aerodynamics. This may not be critical but you'll need to learn about this characteristic of your plane, and fast, so you can fly it properly.

The small trim tabs located on the transmitter are used to fine-tune the controls. These too can vary from one transmitter model to another. What you are doing is putting in a constant adjustment to the flying controls to balance the defect affecting the airplane.

Once the trim tab has been moved, allow your model plane to fly on its own for about 10 seconds to check that it is flying straight and level, and then, if necessary, you can make further small adjustments until you get it right.

Tips 3 : Taking Off

The way you take off will depend on a number of things. For example, if your model plane is designed with an undercarriage and you’re flying from a flat, smooth surface, then you would do better taking off from the ground instead of using a hand launch. To do this, you go through all of your pre-flight checks and then set the plane on the “tarmac,” facing into the wind.

Next, stand directly behind the plane. Turn the engine on to full power, allowing the airplane to accelerate while on the ground. If necessary, use the rudder to keep the plane headed straight down the runway. Just as with a full size plane, the model will gain speed and eventually lift off the ground.

Lift Off
When the plane starts to take off, give it just a little bit of up elevator. Typically you see beginners make the mistake of climbing too steeply, which causes the plane to slow down, stall, and crash. A gradual climb, as stated before, is much better. So go light on the up elevator.

Launch
If you plan to hand launch your model plane, be sure you never throw it angled up. Instead, it should be thrown firmly --but not too hard--with the nose pointed straight ahead. You want it in a nice stable flying position while you get your hands back on the transmitter box.

Friday, May 4, 2007

Tips 2 : Test Glide

Although not all flyers will perform a test glide at every outing, you will certainly want to consider this whenever you are dealing with a new model. The test glide is designed to assess the glide characteristics of the plane, so you know what to expect if the engine should unexpectedly quit for any reason. To do this, you want to work over a long area of grass, so if something happens, the model airplane will not be seriously damaged.

For the pre-flight check, turn the transmitter on first, followed by the receiver switch. Then, pull the transmitter antenna out so that it's completely extended. Next, make sure the rudder or elevator is working properly, moving in the correct way then centre it in a neutral position.

Now hold your airplane facing away from you, at head level and into the wind. Very gently launch the plane from your hand, making sure it is level or pointed slightly downwards. If the plane is right and ready to fly, it will gently glide to the ground after a short, smooth flight.

Tips 1 : Weight and Balance

For RTF kits (that's Ready To Fly), you don't need to worry much about the weight and balance when you first buy the plane. However, you should always check the balance before each flight. If the airplane is not balanced, it will likely crash. Planes, whether model or full size passenger jets, all have a center of gravity which must be within certain limits for the aircraft to fly successfully.

This has a direct impact on the plane's balance. As a general rule, the center of gravity should be about one-third of the way back from the front edge of the wing (and two-thirds of the “wing-chord” forward from the trailing edge). To test, place the tips of your index fingers under the wing tip, about one-third of the way back from the leading edge.

Then, very carefully, lift the model airplane up, balancing it on your fingers. If the balance is good, the plane will be level, with the nose pointing horizontal, or maybe just a bit downward. If the plane's tail is pointing downward, then you have a balance problem and should not fly the plane until it is fixed.

Before adjusting it, think of what might have caused it. If you tested your model before leaving home and it was OK but now it isn't then what might be the cause? A loose screw or piece of material which has moved around during transit can be enough to affect the CG. If you now adjust it back to balance by adding another weight then you may have left a loose item inside your model which will surely come back to haunt you when it moves again during a flying manoeuvre.

If you are sure you have nothing loose and you do need to adjust the CG, add weight to the nose, something like fishing shots, plasticine, or even modelling clay. Add just a little at a time, checking the center of gravity after each addition. (Or, you can move the engine more toward the front.) If you do not want to lose control and maybe crash and ruin your plane, this is a crucial step.

Tuesday, May 1, 2007

Benefits of RC Flight Simulator

A flight simulator is an excellent tool if used properly. The big mistake that so many people make is to believe that the simulator will teach them to fly. A simulator cannot teach anything. They are simply not programmed with that ability. Many software packages have a built-in tutorial that allows the user to step through the functions of the program as it explains how to use each one. The simulator does not have this feature. For instance, the simulator does not explain that stick movements should be gentle and only enough to get the model to perform a maneuver. It does not explain that the model must be controlled into and out of a turn with the ailerons. These are the functions of an instructor. The simulator is a tool to practice the maneuvers that have been taught by an instructor. A student pilot, especially a beginner, can develop some very bad habits while using a simulator that are difficult to break later.

For beginners, flight simulators are excellent tools for building spatial orientation, motor skills, and confidence. For more experienced pilots, flight simulators help in building motor skills required in doing the more difficult maneuvers. The amount of benefit that the pilot can gain from the simulator depends entirely on how well the simulator emulates the model. On most simulators, the flight characteristics can be adjusted so that it more closely emulates the "feel" of the model. None of the simulators have progressed to the point that the flight physics are perfect but they are close enough that they can be of significant benefit.

Dne of the most difficult things to master for the beginning pilot is approach orientation. There is a natural tendency for the beginner to move the stick in the direction he wants the model to go. When the model is moving toward the pilot, the aileron and rudder controls are reversed. This means that in order for the model to turn to the pilot's left, the stick must be moved to the right. Using a simulator allows the pilot to practice approaching maneuvers for hours on end so that it becomes second nature to move the stick in the correct direction for the model to take the desired flight path. After approach orientation has been mastered, all other maneuvers start to become easier to accomplish, especially landings.

The primary benefit of flight simulators is that of building motor skills. The pilot, whether a beginner or experienced, can practice specific maneuvers for hours without having to be concerned about weather, time of day, temperature, or number of people at the field. The motor skills that are developed through hours at the simulator are basically the same as "muscle memory" in golf. This means that the skills are related more to the muscles reacting to a simple command than the brain sending a series of commands to the muscle. For instance, the pilot wants to perform a snap roll with a Giles 202 model. He thinks "snap roll" and his fingers simply move the sticks to the appropriate position rather than his having to think in what position the sticks need to be. The end result of the muscle memory is where modelers get the term "feel" for a model. Since there is no positive feedback system built into a transmitter, there is not true feel for a model. The feel of the model comes from the difference in the expected feel based on muscle memory and the actual feel from the movement of the sticks.

Many beginners do not progress as well as others simply because of a lack of confidence. This is especially true if the student is not able to fly very often due to conflicts in scheduling time to devote to learning to fly. With each trip to the field, he must re-learn some of the things that he has forgotten during his absence from the field. He must again reinforce his motor skills and regain his muscle memory or feel for the trainer. Since his progress may be much slower than that of other students at the field, he may become frustrated and much less confident. The simulator allows the beginner to practice what he has learned to maintain or improve his motor skills and not lose his confidence. When he goes to the field, he will subconsciously think, "I can do this."

If pilots get proper instruction and use the flight simulator to practice what is taught, it can be of significant value in learning to fly or to perfect various maneuvers. It can greatly increase the "stick time" that the pilot is able to achieve in given period of time. It is a tool that if properly applied can help a pilot to progress at a much faster rate than normally possible. Above all, it is up to the pilot to make sure that this tool is properly applied by getting the right kind of instruction and not try to learn on his own.

RC Switch for Radio Control

Parts List
All resistors 1/4w / 5% tolerance, unless otherwise posted.

R1 = 47K
IC1 = MC14013B
R2 = 1K
Q1 = BUZ11, IRFZ42, NTE2395, or ECG2395
R3 = 10K
S1 = on/off switch (optional)
P1 = 100K

Servo Lead
C1 = 22nF

The MC14013B dual type D flip-flop is constructed with MOS P-Channel enhancement mode devides in a single monolithic structure. Each flip-flop has independent Data, (D), Direct Set, (S), Direct Reset, (R), and Clock, (C), inputs and complementary outputs (Q and Q-not). These devices may be used as shift-register elements or as type 'T' flip-flops for counter and toggle applications. The MC14013B CMOS SSI is a low-power complimentary MOS.

This device contains protection circuitry to guard against damage due to high static voltage or electric fields. However, precautions must be taken to avoid applications of any voltage higher than the maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range Vss [much-smaller-than] (Vin or Vout) [much-smaller-than] Gnd. Unused inputs must always be tied to an appropriate logic voltage level (e.g. either Vcc or Gnd). Unused outputs must be left open.

Description
The circuit, as described above, is a so-called "Radio Controlled Electronic Switch". It can be used to switch on/off anything electrical, whatever it is. Here are a couple of examples : navigation lights, landing gear, sound systems, glow plug driver, bomb release, parachute, search lights, gyros, and so on.

Fig. A shows the regular setup for common accessories such as motors, glow plugs, bomb-doors, relays, etc. If you like to hook it up to a camera, see Fig. B. Note that for the Camera Shutter version the value for R1 and R2 is different (100K). Please note that this system will not work with PCM.

Heart of the circuit is a CMOS Dual 'D' Flip-Flop MC14013B. The input Flip-Flop is designed as a monostable pulse generator by means of R1, P1 and C1 connected between 'Q' and the RESET input, which produces a preset pulse-length set by the adjustable potentiometer and starts at the rising edge of the input pulse. When this monostable times out it's inverted 'Q' signal goes high and clocks the output stage of the Flip-Flop, which is used as a normal type 'D', to sample the input pulse. If the duration of the input pulse is longer than the preset monostable pulse, then a logic high level will be clocked to the output of the 'D' type. A shorter input pulse will cause a logic low to be clocked to the output. In short, both halves of the IC perform two different logic functions.

The output drives the output device which in this circuit is the IRFZ42 TMOS FET. It needs only 2-volt on it's gate to fully turn-on and has an rDS-ON resistance of only 0.028 ohm. To invert the operation of the r/c switch, you can connect R2 either to pin 12 or 13 of the MC14013B. This circuit is easy in design and to built and can easily be done using vector board, vero-board, or whatever. The complete unit measures 5/8" by 1-1/4" but it can be a lot smaller by choosing SMT components, probably 3/8" x 1/2". You can use a case or heat-shrink. This unit is NOT meant as a motor-switch for electric flight.

Adjusting the Switch
To test the unit hookup a light and a battery, making sure the + of the battery goes to the Drain of Q1. Adjust the potentiometer P1 to somewhere in the middle and set the transmitter function of your choice (say the throttle) to the point where you wish to switch the unit. Now adjust the potentiometer P1 to the point the light comes on. If it does, your unit functions properly and you can play with whatever other setup you have in mind. If you intend to use this unit as a on-board glow driver, make sure to use heavy wiring between glow plug, battery and r/s switch. A 'Y'-lead to the throttle servo is required. If you use this unit to switch relays or a small dc-motor, then a 'spark eliminator' diode (1N4001) is required. Cathode of the diode goes to the '+' side of the battery. (See diagram).
At the top you see the Surface Mount version (SMT), measuring 15mm x 17mm!

The IRFZ42 is a TMOS Power FET and can be costly (approx. S$18). Other substitutes like the IRFZ44 will work too. Watch for static discharge with this one!

IC1, the MC14013B, is a CMOS SSI type Dual Flip-Flop. It features a direct pin-for-pin replacement with the CD4013B, NTE4013B, ECG4013B, and others.

The output signal can be inverted by selecting either pin 12 or 13. To make life easier, you could install a miniature on-on switch.

The middle contact going to R2, and pin-12 & 13 to the other two contacts.
Powered By Blogger